How to Install a PVC Fence

There are some things to keep in mind if you're thinking of installing fencing. First, determine the location where you would like the fence to be erected. The next step is to prepare the ground. Next, you will need to place the posts. You may also need to adjust the height depending on the size and shape of your house.

Preparing the ground

It is essential to prepare the ground for the plastic fence panels. This is because fence posts need to be securely buried. If they aren't secured, brown Vinyl Fences the fence could easily blow over in the wind.

Before digging, make sure to check with your local utility company to make sure that there aren't any underground utilities that might hinder the installation. Call 811 to mark your yard for underground lines.

You should also prepare a gravel base for your fence post. This will allow water to drain from the posts. It also provides a sturdy foundation on which blocks will be built on top of it.

Once you have the base, it is time to install the vinyl fence. The fence must be at least four feet long and one-inch thick. If you have access to an auger, you should use it to dig holes for fence posts.

Before digging, Brown Vinyl Fences clear any shrubs or plants that could block the hole. In certain situations it is easier to remove the ground before digging it. If you do need to dig, it is best to avoid digging in rocky or sandy soil.

The next step is to mark the high and low points of your yard. This is easiest done by using the string level. Attach the string level to stakes that are about one foot above the ground. The string level will act as a guideline for the fence posts.

If your property is in a very dry climate, you will probably require pre-drilling pilot holes. This will help the process run much more quickly.

You will also need to mark the holes. Spray paint or a marker to mark your holes. You can also make use of a mason's line to ensure that the posts are straight.

You can also fill the gap with decorative stones. These stones are perfect for smaller gaps. However should there is a larger gap, you'll require a different approach. It is also possible to put dirt in the gap. This can be a cheap and efficient solution.

Placement of the posts

It can be difficult to place the posts. First, locate the right spot. This can be done using the use of a spirit level, a line mark that has been painted to fit the width of the post or a measuring wheel.

Then, put the end and corner posts in their place. Also, put in the middle and top rails. Some cutting may be necessary. You could also use rails to act as a spacer between the posts.

After you have determined the center of each hole using a tape measure or stakes, mark the middle of the posts with a tape measure. To determine the depth, you could also draw a stringline. Once the string line is drawn, tie the ends of the end post to the string. This will ensure that the fence is straight.

After the posts have been securely set and the posts are in place, fill the bottoms with 6 inches of gravel. This will keep the posts in place, and also provide drainage.

When you set the fence posts in concrete, be sure to use quick setting concrete. Concrete that is set this way sets within three to four minutes. You should not tighten the panels when installing privacy fencing. The panels should be positioned 22 inches above ground. The panel is to be secured using #10 1" self tapping stainless steel screws.

If you are installing a brown vinyl fences - Our Web Site, fence, you can secure the posts to the lower collars by using two screws. If you are building privacy fence you should leave one screw at the top rail. Duct tape can be used to cover the bottom rails prior to putting them into the posts. This stops concrete from getting into the horizontal rails at the bottom.

After you are satisfied with the arrangement, take off the duct tape. Then, slide the top rail into each of the posts. The pickets can be attached to the rails.

You can also connect the rails at the bottom to the corners. You can use aluminum u-channel to attach the rails to the post.

Assembling the panels

Getting the fence posts lined properly is crucial for the success of installing a vinyl fence. Based on the design of your fence, you may require different methods. These steps will help you determine whether you're planning to construct a square or oval fence.

Before you begin, be sure to read your deed and local zoning laws. Notify neighbors of your plans. You may require a building permit for installing an electric fence.

Once all your posts are set Once all your posts are in place, it's time to attach your rail brackets. These screws are placed on the inside of the post. This allows for more control of the posts when they are inserted.

Before you attach your rail brackets, be sure you install your bottom rail. colored vinyl fences panels pre-assembled have two rails. You may have to cut the rails to fit your terrain.

Once the bottom rail is in place, you can then install the middle rail. The top rail can be put in place in the same manner. You can utilize an aluminum uchannel for this step. It can be put into your posts with #8 x 1'’ screws.

The pickets are then placed one at a time. Once your pickets are installed then attach your C channel brackets. You can also place stakes around the corners to keep them in place. You can also use cotton string to join the stakes.

Spray paint markers can also be used to mark your fence. This will ensure that the fence is straight when it is set.

Finally, you will have to install privacy panels. These should be installed on the back side of your fence. To help them stay in place, you could also add pea gravel. You can make your slope more gentle by putting your fence panels on one side so that they "step down". If the slope is steep your fence will need to be built so that it "steps down".

Problems with height changes

It may be difficult to align the posts if you want to build a PVC fence. There are two methods to do it. The first is to lay the posts on the ground. The other option is to line them up. The first method is less complicated and ensures that concrete is placed under and around each post. The second method requires digging out the posts, and then backfill with dirt.

When you remove the posts, be sure that you have a sufficient backfill and dig the holes enough to hold three-quarters of the length of the post. You'll need to dig around six inches to insert the posts into the bottom of the gravel. To drill the holes, you could make use of a hole-drilling machine. In the final step, hook up the tension bar to the mesh. Attach the steel mesh at the top of the fence.

If you are having trouble aligning the posts, you can eliminate any rails from the posts that are too high. This is a challenging process however you should be able do it if you have two persons helping you. If you own a hammer and chisel, you can use them to tack the bolts' threads. This will keep them from escaping the fence when you remove it.